Sale!

Optimum Energy Management System

Model: 19
555 in Monstable & Astable, 7 Segment Display, 8051 Microcontroller, Energy saving, IR Sensor, Relay Switching, Visiter Counter

Solderable DIY project kit for Engineering & Diploma students

Product of choice for Engineering & Diploma students worldwide.

Do-It-Yourself Kit :

Includes complete hardware comprising of discrete components, modules, PCB, controller etc. and tested program code for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. (Tool kit-Multimeter, Soldering iron and program burner not included in the kit)

Rs.3,699.00 Rs.2,774.00
DISCOUNT 25 % OFF

DESCRIPTION



Overview

The energy consumption of buildings represents a large part of the world’s total energy consumption. In order to achieve this project is developed to monitor the number of persons entering as well as exiting a room. This is a preferred way of controlling electrical loads by ‘switching on’ the lights as the first person enters, and then switching off as the last person leaves.

This application is an automation system to save energy. In this project, a 555 timer driven at 38 KHz signal to an IR LED gets interrupted on to the IR receiver, to sense the person entering as well as exiting the room, and which is then fed to a 555 timer. There are two pairs of sensors, each kept at a certain distance from each other. One pair of sensor consists of a transmitter and a receiver, kept exactly opposite to each other. The output of the 555 timer is fed to the Microcontroller for analyzing and control purpose. . The transmitting part emits modulated IR light which is received at the receiver end and fed to a microcontroller. The data obtained from the microcontroller is given to a 7-segment display unit, which displays the number of persons entering, and exiting. A relay is used to control any load for alerting through its ‘NO’ contacts, which is interfaced with the microcontroller through a relay driver.

The power supply consists of a step-down transformer 230/12V, which steps down the voltage to 12V AC. This is converted to a DC using a Bridge rectifier. The ripples are removed using a capacitive filter, and it is then regulated to +5V using a voltage regulator 7805, which is required for the operation of the microcontroller and other components.

Furthermore, the system’s efficiency can be heightened by using a timer arrangement in the project so that if the load switching doesn’t take place for some reason as desired, then the timer would complete the task after a prefixed time.

DIFFERENTIATORS

Easy to use, Self-explanatory kit.

All-inclusive solution kit.

Extensive audio-visuals available.

Branding-free material.

Pre-programmed Microcontroller.

Call/mail for Tech Support from 10 am – 7 pm.

Can be Customized for Arduino, Raspberry Pi, PIC

TECH SPECS

Hardware Requirements

  • 8051 series Microcontroller
  • Voltage Regulator
  • Resistors
  • Capacitors
  • 7- Segment Displays
  • Push Button
  • Diodes
  • 555 Timers
  • Relays
  • LED
  • Transistor
  • IR LED’s
  • IR Receivers
  • Lamp

Software Requirements

  • Keil compiler
  • Language: Embedded C or Assembly

Q & A

Buyer Feedback

Write a new review
  1. Rated 4 out of 5

    Uppili@pranavane

    I got to know about Edgefx while I was searching for projects in Google. Since Edgefx is providing Readymade kit also so decided to buy my project from Edgefx. I liked the explanation of video. Purchased through online. For me things are fine and not facing any problems so no changes keep doing the same work.

  2. Rated 4 out of 5

    Shalmali Kakde

    Mr. Harshad delivered to me on right time with the right components. Initially I have a doubt but it is cleared by your team. The technical support is good.The Soldering kit should be good enough. I recommended to my college juniors.

  3. Rated 4 out of 5

    Deepak mohakud

    I came to know about Edgefx through Internet. I used the project title in the Google to find Edgefx.I thought Service and kit may be good. And even my senior bought his project from Edgefx I like it’s not expensive.Yes the kit delivered on time with the right components.I purchased the project through online. FedEx delivery should be improved.

  4. Rated 4 out of 5

    Nadeem Iqbal

    I come to know about Edgefx through Internet.I decided to take, because my project is available in your website.Yes the kit delivered on time with the right components.I purchased through online.No Suggestions.

  5. Rated 4 out of 5

    Nadeem Iqbal

    I come to know about Edgefx through Internet.I decided to take, because my project is available in your website.Yes the kit delivered on time with the right components.I purchased through online.No Suggestions.