Sale!

Dual Converter using Thyristors

Model: 290

Solderable DIY project kit for Engineering & Diploma students Worldwide

Do-It-Yourself Kit :

Includes complete hardware comprising of discrete components, modules, PCB, controller etc. and tested program code for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. (Tool kit-Multimeter, Soldering iron and program burner not included in the kit)

Rs.4,499 Rs.3,824
Discount 15 % Off

DESCRIPTION

Overview

Dual converter is a power electronics control system to get either polarity DC from AC rectification by forward converter and reverse converter . It can run a DC motors in either direction with speed control too .This single phase converter is achieved by using a pair of thyristor controlled bridge (4 SCRs X 2 ) that enables the DC motor to get reversed polarity for either direction rotation and speed control also lowered in steps by Microcontroller triggering each bridge SCR bank of duly interfaced through opto-isolators.

A pair of switches is used to input logical signal for the desired output. If input of 230 volt ac is given to the dual SCR bridge we can have a 100 watt lamp load and the DC polarity across the lamp is checked. Alternatively we can use 12 volt ac at the input and a 12 volt DC motor to verify either direction rotation as the polarity gets reversed.

The power supply consists of a step down transformer 230/12V, which steps down the voltage to 12V AC. This is converted to DC using a Bridge rectifier. The ripples are removed using a capacitive filter and it is then regulated to +5V using a voltage regulator 7805 which is required for the operation of the microcontroller and other components.

DIFFERENTIATORS

Easy to use, Self-explanatory kit.

All-inclusive solution kit.

Extensive audio-visuals available.

Branding-free material.

Pre-programmed Microcontroller.

DC motor capacity upto 1KW.

Call/mail for Tech Support from 10 am – 7 pm.

Can be Customized for Arduino, Raspberry Pi, PIC

TECH SPECS

Hardware Requirements

  • Microcontroller
  • Crystal Oscillator
  • SCRs
  • Opto- isolators
  • switches
  • LED
  • Transformer
  • Diodes
  • Operational amplifiers
  • Capacitors
  • Resistors
  • Lamp or a 12 volt DC motor

Software Requirements

  • Keil compiler
  • Language: Embedded C or Assembly

Q & A

Buyer Feedback

Write a new review
  1. Rated 4 out of 5

    Ranjith L

    I came to know about Edgefx through one of my senior. I decided to buy a kit from Edgefx by the words of my senior Purchased directly through online.

  2. Rated 4 out of 5

    Vinay kumar

    I came to know about Edgefx while I was searching for my Academic project in Google along with my friends. Since Edgefx is providing project kit also so decided to buy my project from Edgefx. I liked the circuit diagrams and explanation of video. I placed an order through online.

  3. Rated 4 out of 5

    Amit verma

    Yes the kit delivered on time with right components.All my technical queries were cleared. And I give 5 out of 5 for the technical support.I was well satisfied in building the project.Not yet, but I will definitely recommend in future.

  4. Rated 4 out of 5

    Amit verma

    Mr.Alok delivered the kit to me with all the components.Yes I got a lot of queries while building the project and all were cleared. I rate 9 out of 10 for Edgefx support.It’s difficult but Edgefx material and service helped a lot.I recommended to my school friends.

  5. Rated 5 out of 5

    Ranjith L

    I came to know about Edgefx through my senior. I directly typed Edgefx kits in Google.I decided to buy a kit from Edgefx by the words of my senior. And I like the complete kit.Yes the kit delivered on time with the right components. Very nice kit, no Improvements required. I will recommend Edgefx in future.