Hi Guest
e.g. - "communication: RFID" Search tips
Find Projects
Model: 290    

Solderable DIY project kit for Engineering & Diploma students

Product of choice for Engineering & Diploma students worldwide.

Do-It-Yourself Kit


Rs. 5,299

Rs. 3,180

Includes complete hardware with plain PCB and a pre-programmed controller for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. Thorough understanding from the Problem definition to Circuit Design to Programming, Testing, Troubleshooting and finally building a working hardware project.

Tool Kit


Rs. 350

Includes Digital Multimeter, Soldering Iron, Screw driver, Cutter, to be used with Do-It-Yourself Kit to build the project.

Loaded and Tested PCB


Rs. 2,399

Rs. 1,440

Pre-soldered and tested PCB. Choose this option only if you are short on time. Only works along with the Do-It-Yourself Kit.

Total Rs. 0

Rs. 0 ( You Save Rs. 0 )



Dual converter is a power electronics control system to get either polarity DC from AC rectification by forward converter and reverse converter . It can run a DC motors in either direction with speed control too .

This single phase converter is achieved by using a pair of thyristor controlled bridge (4 SCRs X 2 ) that enables the DC motor to get reversed polarity for either direction rotation and speed control also lowered in steps by Microcontroller triggering each bridge SCR bank of duly interfaced through opto-isolators.

A pair of switches is used to input logical signal for the desired output. If input of 230 volt ac is given to the dual SCR bridge we can have a 100 watt lamp load and the DC polarity across the lamp is checked. Alternatively we can use 12 volt ac at the input and a 12 volt DC motor to verify either direction rotation as the polarity gets reversed.

The power supply consists of a step down transformer 230/12V, which steps down the voltage to 12V AC. This is converted to DC using a Bridge rectifier. The ripples are removed using a capacitive filter and it is then regulated to +5V using a voltage regulator 7805 which is required for the operation of the microcontroller and other components.

Easy to use, Self-explanatory kit.
All-inclusive solution kit.
Extensive audio-visuals available.
Branding-free material.
Pre-programmed Microcontroller.
DC motor capacity upto 1KW.
Call/mail for Tech Support from 10 am - 7 pm.
Can be Customized for Arduino, Raspberry Pi, PIC
Dual Converter using Thyristors
Hardware Requirements
  • Microcontroller
  • Crystal Oscillator
  • SCRs
  • Opto- isolators
  • Transformer
  • Diodes
  • LED
  • Switches
  • Capacitors
  • Resistors
  • Operational amplifiers
  • Lamp or a 12 volt DC motor
Software Requirements
  • Keil Compiler
  • Languages: Embedded C or Assembly
Q & A
Q:  What is dual converter?
A:  Dual converter is a power electronics control system to get either polarity DC from AC rectification by forward converter and reverse converter using 2 full bridge SCR's.
Q:  Which microcontroller is used in this project?
A:  A 40 pin microcontroller from 8051 family is used in this project.
Q:  What is the formula for calculating smoothing capacitor value?
A:  There is some approximated formula .Peak to peak ripple voltage = Load current in amps / (2*line frequency in hertz *capacitance in farads). But as rule of thumb for 1 A current 1000uF is best. Thus it is load dependent.
Average Rating
Please enter security code
Showing 4 of 9 reviews Show All
Ranjith L, Mysore on 20th November, 2015, 05:29 PM

I came to know about Edgefx through one of my senior.
I decided to buy a kit from Edgefx by the words of my senior
Purchased directly through online.

vinay kumar, New Delhi on 18th November, 2015, 11:53 AM

I came to know about Edgefx while I was searching for my Academic project in Google along with my friends.
Since Edgefx is providing project kit also so decided to buy my project from Edgefx. I liked the circuit diagrams and explanation of video.
I placed an order through online.

Amit verma, Delhi on 30th May, 2015, 05:04 PM

Yes the kit delivered on time with right components.All my technical queries were cleared. And I give 5 out of 5 for the technical support.I was well satisfied in building the project.Not yet, but I will definitely recommend in future.

Amit verma, Delhi on 30th May, 2015, 04:46 PM

Mr.Alok delivered the kit to me with all the components.Yes I got a lot of queries while building the project and all were cleared. I rate 9 out of 10 for Edgefx support.It’s difficult but Edgefx material and service helped a lot.I recommended to my school friends.

Rating Breakdown (9 Reviews)

Only Tool kit can not be purchased individually.


Edgefx Technologies Pvt. Ltd.,
Plot No. 105, 3rd Floor,
Liberty Plaza, Himayathnagar,
Hyderabad - 500029,
Telangana, India
© 2012 Edgefx Technologies Pvt Ltd. All Rights Reserved