Hi Guest
e.g. - "communication: RFID" Search tips
Find Projects
Model: 35A    

Solderable DIY project kit for Engineering & Diploma students

Product of choice for Engineering & Diploma students worldwide.

Do-It-Yourself Kit

Rs. 5,269

Rs. 3,583

Includes complete hardware with plain PCB and a pre-programmed controller for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. Thorough understanding from the Problem definition to Circuit Design to Programming, Testing, Troubleshooting and finally building a working hardware project.

Tool Kit


Rs. 350

Includes Digital Multimeter, Soldering Iron, Screw driver, Cutter, to be used with Do-It-Yourself Kit to build the project.

Loaded and Tested PCB


Rs. 1,119

Rs. 896

Pre-soldered and tested PCB. Choose this option only if you are short on time. Only works along with the Do-It-Yourself Kit. (Can be purchased later)

Total Rs. 0

Rs. 0 ( You Save Rs. 0 )



The project is designed to develop a robotic vehicle that is controlled by a cell phone. DTMF commands from a phone are sent to another cell phone which is mounted on the robot. These commands are fed to a microcontroller of 8051 family to operate the vehicle movement through motor interface.

The main scope of project is to send commands from one cell phone to be received by another cell phone mounted on the robot to receive the DTMF (Dual Tone Multi Frequency) mode commands which are then decoded by a DTMF decoder.

The corresponding codes are then fed to a microcontroller, programmed to recognize those codes to operate 2nos DC motors through motor driver IC for any direction movement as per the sent commands from sender’s mobile. The motors are controlled using motor driver IC which is interfaced to the microcontroller. It uses microcontroller from 8051 family and a battery for power source.

Further the project can be enhanced by interfacing it with additional motors for multipurpose activity. For example, it can be developed into pick n place robot or fire fighting robot with water pump etc.


1) This line following robot can also be modified to a walking robot in any surface by using only one motor with homemade fixtures as per the detailed instructions give.

2) Similarly the same walking robot can be attached with special magnetic material as per instructions to climb a wall of any vertical metallic surface say a refrigerator body.

Please find the link below:


Easy to use, Self-explanatory kit.
All-inclusive solution kit.
Extensive audio-visuals available.
Branding-free material.
Pre-programmed Microcontroller.
Call/mail for Tech Support from 10 am - 7 pm.
Can be Customized for Arduino, Raspberry Pi, PIC
Hardware Requirements
  • 8051 series Microcontroller
  • Crystal
  • DTMF Decoder IC
  • Motor Driver IC
  • DC Motors
  • Batteries
  • Robot Body
Software Requirements
  • Keil compiler
  • Language: Embedded C or Assembly.
Battery not included in the kit due to Courier service prohibition. Please buy four AA CELL 1.5V batteries for this project.
Q & A
Q:  Which microcontroller is used in this project?
A:  A 40 pin microcontroller from 8051 family is used in this project.
Q:  Can this project be implemented using the landline phone?
A:  No, this project has been designed to be implemented with only a mobile phone.
Q:  What is DTMF?
A:  DTMF or Dual tone multi frequency is a signaling system which uses a combination of two frequency tones to represent a key pressed on the keyboard of any cell phone.
Q:  What are keypad tones?
A:  Keypad tones are the audible sound heard, when a key is pressed on the mobile phone.
Average Rating
Please enter security code
Showing 4 of 7 reviews Show All
Supriya Bharati, Ahmedabad on 2nd June, 2015, 04:02 PM

I came to know about Edgefx through Internet I used Keyword online projects India to find Edgefx. I decided the project to buy a kit from us I like the complete kit.Yes the kit delivered on time with the right components.No Suggestions.

Ankita Anand, Kolkata on 2nd June, 2015, 01:06 PM

I came to know about Edgefx through Internet.I decided to buy from Edgefx because while along with the project I am getting contents like Documentation & PPT’s.Yes the kit delivered on time with the right components.No I purchased through online.No Suggestions required.

Vaibhav bindal, Jaipur on 13th May, 2014, 05:44 PM

I purchased the project from Edgefx because it was been recommended by our Deputy HOD. I like the softcopy very much because complete information is involve in this.Better to pack the components by checking twice.

Aman Kakuar, on 11th June, 2013, 12:16 AM

Question were about how start the project and how to use the components and equipment that were accessory in this project.Doubts have been cleared thanks to Edgefx dealer JauhariInfotech-Allahabadand hesitations are less as compared to the confidence build up so far. You provide the quality kit the reliability of the components and more over a guidance which was most for us. The kit covered every part of equipment and some were in spare I like the things such as millimeter , soldering iron , etc . You are on the way of consistence improvement

Rating Breakdown (7 Reviews)

Tool kit cannot be purchased individually.


Edgefx Technologies Pvt. Ltd.,
Plot No. 105, 3rd Floor,
Liberty Plaza, Himayathnagar,
Hyderabad - 500029,
Telangana, India
© 2012 Edgefx Technologies Pvt Ltd. All Rights Reserved