Hi Guest
e.g. - "communication: RFID" Search tips
Find Projects
Model: 491    

Solderable DIY project kit for Engineering & Diploma students

Product of choice for Engineering & Diploma students worldwide.

Do-It-Yourself Kit


Rs. 6,599

Rs. 3,960

Includes complete hardware with plain PCB and a pre-programmed controller for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. Thorough understanding from the Problem definition to Circuit Design to Programming, Testing, Troubleshooting and finally building a working hardware project.

Tool Kit


Rs. 0

Includes Digital Multimeter, Soldering Iron, Screw driver, Cutter, to be used with Do-It-Yourself Kit to build the project.

Loaded and Tested PCB


Rs. 0

Pre-soldered and tested PCB. Choose this option only if you are short on time. Only works along with the Do-It-Yourself Kit.

Total Rs. 0

Rs. 0 ( You Save Rs. 0 )



This project is intended to control a single-phase A.C. induction motor using a new method of speed-control technique. It presents a design of a low-cost high-efficiency drive capable of supplying a single-phase A.C. induction motor with a PWM modulated sinusoidal voltage. The circuit operation is controlled by the microcontroller of the 8051 family.

The device is aimed at substituting commonly used TRIAC phase angle control drives. This circuit is capable of supplying single-phase A.C. induction motor (or general A.C. inductive/resistive load) with varying A.C. voltage.

The same as in the TRIAC control, the voltage applied to the load can be varied from zero to maximum value. On the other hand, it uses a pulse width modulation technique (PWM), and when compared to the phase-angle control used for TRIACS, it produces much lower high order harmonics.

Thus, it suits EMC/EMI regulations much better. Because the circuit is aimed at low-cost, low/medium-power applications, it does not use a conventional converter topology to produce output voltage waveform. It directly modulates the mains A.C. voltage.

Compared to costly converter, it requires lower number of active and passive power components. In summary, a device attempted here takes advantage of both low price of the phase-angle control and low harmonic content and high efficiency that we can get with standard converter topology.

The drive uses PWM controlled MOSFET and load in series with bridge rectifier. This drive based on this new control technique is targeted for use in consumer and industrial products: washing machine, dishwashers, ventilators, compressors, and wherever system cost is a consideration.


The input terminals of the rectifying bridge are connected in series to the load. The output terminal (rectified side) has a power transistor (IGBT, MOSFET or bipolar) connected across them. When the power transistor is off, the current cannot flow through rectifying bridge and load which is in series remains in off-state.

When the power transistor is on, the bridge output terminals are short-circuited, and then, the current can flow through the rectifying bridge and thus through load. Thus, by changing the duty cycle of the PWM pulses to the power switch ,the power to load is controlled. Special care is taken in circuit such that PWM pulses are synchronized with supply phase by zero voltage sensing points.

Easy to use, Self-explanatory kit.
All-inclusive solution kit.
Extensive audio-visuals available.
Branding-free material.
Pre-programmed Microcontroller.
Call/mail for Tech Support from 10 am - 7 pm.
Can be Customized for Arduino, Raspberry Pi, PIC
AC PWM based Power Control by IGBT / MOSFET
Hardware Requirements
  • 8051 series Microcontroller
  • LM358
  • Opto- isolators
  • IGBT
  • Push Button
  • Transformer
  • Diodes,Voltage Regulator
  • Resistors
  • Capacitors
  • Zener
  • Crystal
  • Lamp
Software Requirements
  • Keil compiler
  • Languages: Embedded C or Assembly
Q & A
Q:  Which microcontroller is used in this project?
A:  The microcontroller used in this project is a 40 pin IC from 8051 family.
Q:  Can I place motor instead of lamp?
A:  Yes up to ¼HP 230V AC motor can be used
Q:  What is ACPWM control?
A:  It presents a design of a low-cost, high-efficiency drive capable of supplying a single-phase AC induction motor with a PWM modulated sinusoidal voltage by chopping the AC wave form.
Q:  Can the input voltage variation to 168 be provided by any circuit without a variac?
A:  Add our model 344 at the input to 168 link for getting variable HV DC at the output.
Average Rating
Please enter security code
Showing 2 of 2 reviews
Ashish Deshpande, Pune on 19th November, 2015, 05:17 PM

I came to know about Edgefx through one of my senior.
I decided to buy a kit from Edgefx by the words of my senior. And I like the complete kit.
Purchased directly through online.

Ashish Deshpande, Pune on 15th June, 2015, 10:37 AM

I am working in a company named Ansys and we deal with power simulation based projects like space vector modulator. so while browsing I go to know about Edgefx.For the Collaboration I take the kit from Edgfx. Yes it is perfect and working properly even.Through online I got this kit.

Rating Breakdown (2 Reviews)

Only Tool kit can not be purchased individually.


Edgefx Technologies Pvt. Ltd.,
Plot No. 105, 3rd Floor,
Liberty Plaza, Himayathnagar,
Hyderabad - 500029,
Telangana, India
© 2012 Edgefx Technologies Pvt Ltd. All Rights Reserved