Hi Guest
e.g. - "communication: RFID" Search tips
Find Projects
Model: 464    

Solderable DIY project kit for Engineering & Diploma students

Product of choice for Engineering & Diploma students worldwide.

Do-It-Yourself Kit

Rs. 5,599

Rs. 4,480

Includes complete hardware with plain PCB and a pre-programmed controller for building the project. Extensive documentation for project execution including step-by-step instructions for Circuit building, Assembly procedure and Troubleshooting. Thorough understanding from the Problem definition to Circuit Design to Programming, Testing, Troubleshooting and finally building a working hardware project.

Tool Kit


Rs. 0

Includes Digital Multimeter, Soldering Iron, Screw driver, Cutter, to be used with Do-It-Yourself Kit to build the project.

Loaded and Tested PCB


Rs. 0

Pre-soldered and tested PCB. Choose this option only if you are short on time. Only works along with the Do-It-Yourself Kit. (Can be purchased later)

Total Rs. 0

Rs. 0 ( You Save Rs. 0 )



The main concept of this project is to transfer the AC power wirelessly from a power source to electrical loads using a high-frequency resonating air core transformer to develop the frequency from 50Hz to 40KHz for transferring power over a distance of 3cm.

 Wireless power transfer can make a remarkable change in the field of electrical engineering , which eliminates the usage of conventional copper cables and current carrying wires. Based on this concept, the project is developed to transfer the power within a small range.

This project can be used for charging batteries that physically are not possible to be connected electrically such as pace makers (An electronic device that works in place of a defective heart valve) implanted in human body that runs on a battery. The patient is required to be operated every year to replace the battery. This project is designed to charge a rechargeable battery wirelessly for the purpose. Since charging of the battery is not possible to be demonstrated, we are providing a DC fan that runs through wireless power.

This project is built upon using an electronic circuit that converts AC 230V 50Hz to AC 12V, High frequency. The output is fed to a tuned coil forming as primary of an air-core transformer. The secondary coil develops a voltage of HF 12volt. Thus, the transfer of power is done from the primary (transmitter) to the secondary, which is separated with a considerable distance (say 3cm). Therefore, the transfer could be seen as the primary transmission and the secondary receives the power to run the load.

Moreover, this technique can be used in number of applications: to charge a mobile phone, iPod, laptop battery, and propeller clock wirelessly. And also this kind of charging provides a far lower risk of electrical shock as it would be galvanically isolated. This concept is an Emerging Technology, and in future the distance of power transfer can be enhanced as the research across the world is still going on.

Easy to use, Self-explanatory kit.
All-inclusive solution kit.
Extensive audio-visuals available.
Branding-free material.
High-Resonance Frequency Transformer.
Call/mail for Tech Support from 10 am - 7 pm.
Can be Customized for Arduino, Raspberry Pi, PIC
Non-Microcontroller Project.
AC Power Transfer Wirelessly by HF
Hardware Requirements
  • HF-Transformer
  • HF-diodes
  • rectifier
  • Transistors
  • Two air filled inductor coils
  • Voltage regulator
  • BLDC fan
Software Requirements
Q & A
Q:  What is wireless power transfer?
A:  Wireless power transfer is transferring of power wirelessly, using mutual induction of 2 coils in HF.
Q:  What is the concept used in this project?
A:  The project follows the concept of using inverters with high frequency transformers to generate AC signal of higher frequency.
Q:  Can a lamp be used as a load?
A:  Yes, a lamp can be used as a load. Follow the link for model number 343:
Q:  Can I use LEDs instead of fan motor as the load?
A:  Yes, a maximum of 100 white LEDs can be used.
Average Rating
Please enter security code
Showing 4 of 10 reviews Show All
SAURAV MAITY, Chennai on 7th June, 2016, 06:52 PM

We came to know about edgefx is through searching key words Ac power for project in google
By seeing the website it so attractive and it is easy to under
with the right components in right time
support team helped me to purchase kit online
To develop more projects related to all aspects
i will refer this site to our friends
i will go through your blog

Jaswinder singh Sohal, Pune on 4th June, 2016, 05:03 PM

I got to know about edgefx through google. I was searching electronic related projects through that i got to know about edgefx website.
I have decided to buy project from edgefx because i need a kit which is fully assembled. So, that is why i have purchased project from edgefx. I like most about edgefx is fully assembled kit.
the support team has helped me in purchasing the project.
i would like to give reference to my friends and juniors.

M.Rakesh Reddy, hyderabad on 19th November, 2015, 05:28 PM

I came to know about Edgefx when I am searching for the components for my project.
I decided to buy a kit.
Purchased through online.

Arti Satsangi, Agra on 23rd July, 2015, 11:41 AM

I came to know about Edgefx through Internet.I like the fully assembled kit.Yes the kit delivered on time with the right components.I purchased through online.Price should be reduced.

Rating Breakdown (10 Reviews)

Tool kit cannot be purchased individually.


Edgefx Technologies Pvt. Ltd.,
Plot No. 105, 3rd Floor,
Liberty Plaza, Himayathnagar,
Hyderabad - 500029,
Telangana, India
© 2012 Edgefx Technologies Pvt Ltd. All Rights Reserved